Kensington KeyStand Manual download pdf (Page 3)

4 5

NOTE: When you first turn on the Keyboard, both the Power Indicator Light and the

Bluetooth Status Indicator Light glow for 5 seconds. You cannot connect the Keyboard to

your iPad until only the Power Indicator Light glows.

4 On your iPad, tap Settings.

5 Open Bluetooth and make sure Bluetooth is on.

6 On the Keyboard, press the Bluetooth Connection Button. The Bluetooth Status

Indicator Light starts blinking for 10 minutes or until connected to a device.

7 The Keyboard now appears on your iPad screen. Tap Bluetooth Wireless Keyboard.

8 Your iPad screen displays a passkey. Enter the passkey on the Keyboard, and press Enter.

9 Your iPad screen shows the Keyboard as Connected. On the Keyboard, the Bluetooth

Status Indicator Light turns off.

10 You can now use your Keyboard to type in any app.

NOTE: To insure the K Lock key works correctly please ensure you do the following:

Home page > Settings > General > Passcode key. Verify “Require Passcode” is set to

“Immediately” otherwise a keyboard unlock will not require a passcode. Go back to

previous menu and verify “Passcode Lock” is On.

Note the following about the Bluetooth connection between the keyboard and your iPad:

• KeyboardwillgointopairingmodeiftheOn/Off Switch is pressed for 5 seconds or

longer then released (regardless of on or off state).

• PresstheOn/Off Switch for 1.5 to 5 seconds then release = toggle keyboard power

(on to off, off to on).

• Firstturn(Factorydefault,nopriorpairedBTdevices)–enterpairingmode

automatically.

• InONstateonly-Hold“CTRL + FN + F” for 3 seconds or more = reset to factory default

mode (clear all previously paired BT devices in memory), ALL LEDs should flash on and

off 3 times and keyboard should turn to off mode.

• Ifnoactivekeypressfor1minute,theunitshouldgotosleepmode.

• Anytimeakeyispressedinsleepmode,thekeyboardshouldautomaticallyconnectto

last paired iPad if present. If iPad is not found after waking from sleep mode within 30

seconds, the device should go back to sleep.

LED Behavior and Explanation

LED Behavior Explanation

• IftheKeyStandisoff,asleep,orthebatteryisdead,theLEDswillremain

off.

• Initiallyatpower-up,thePower and Bluetooth LEDs will turn on and stay

lit for 5 seconds.

• After5secondstheBluetooth LED will turn off, followed by the Power

LED 0.5s later.

• WhentheBluetooth Connection Button is pressed, the Power LED will

stay solidly lit, while the Bluetooth LED will begin to blink for 10 minutes

or until connected to an iPad.

• Blinkpattern:ON1s,OFF0.5s

• OncetheKeyStandisconnectedwithyouriPad,thePower LED will

remain lit and all others will go off.

• Also,iftheKeyStandisawokenfromsleepmode,thePower LED will turn

on immediately.

• WhiletheKeyStandisconnectedtoyouriPad,thestateoftheCapsLock

toggle is shown by the Caps Lock LED.

• WhentheKeyStandispluggedintoapowersource,theCharge LED will

turn red and turn off only when charge is completed.

Charge the Battery

Charge your KeyStand before initial use or when the Charging Indicator blinks green.

1 Insert the small end of the Charging Cable into the micro USB Charging Connector on

the Keyboard.

2 Insert the other end of the Charging Cable into your iPad charger.

3 Plug your iPad charger into a working outlet. The Charging Indicator Light

glows red.

4 When the Keyboard is fully charged, the Charging Indicator Light turns off.

1 2 3 4 5 6 7 8 ... 39 40

Comments to this Manuals

No comments

Kensington KeyStand Manual Page 3

Comments to this Manuals

Related products and manuals for Mobile device keyboards Kensington KeyStand